1 copyright ? 2010, everlight americas inc. all rights reserved. relea se date : 6.jun.2012. issue no: 1 rev:1 www.everlightamericas.com lamp EALP05RDLBA0 features B popular t-1 3/4 round package. B choice of various viewing angles. B available on tape and reel. B reliable and robust. B the product itself will remain within rohs complian t version . descriptions B the series is specially designed for applications requiring higher brightness. B the led lamps are available with different colors, intensities, epoxy colors, etc. applications B color graphic signs B message boards B variable message signs (vms) B commercial outdoor advertising
datasheet lamp EALP05RDLBA0 2 copyright ? 2010, everlight americas inc. all rights reserved. relea se date : 6.jun.2012. issue no: 1 rev:1 www.everlightamericas.com device selection guide chip materials emitted color resin color ingan blue water clear absolute maximum ratings (ta=25 ) parameter symbol rating unit reverse voltage v r 5 v forward current i f 30 ma peak forward current (duty 1/10 @1khz) i fp 100 ma power dissipation pd 120 mw operating temperature topr -40 ~ +85 storage temperature tstg -40 ~ +100 esd esd hbm 1k v soldering temperature tsol 260 for 5 sec. electro -optical characteristics (ta=25 ) parameter symbol min. typ. max. unit condition radiometric intensity iv 2250 2850 4500 mcd i f =20ma viewing angle 2 1/2 -- 30 -- deg i f =20ma peak wavelength p -- 468 -- nm i f =20ma dominant wavelength d 465 470 475 nm i f =20ma spectrum radiation bandwidth ? -- 26 -- nm i f =20ma forward voltage v f 2.8 -- 3.6 v i f =20ma reverse current i r -- -- 50 a v r =5v
datasheet lamp EALP05RDLBA0 3 copyright ? 2010, everlight americas inc. all rights reserved. relea se date : 6.jun.2012. issue no: 1 rev:1 www.everlightamericas.com bin range of radiometric intensity bin code min. max. unit condition n 2250 2850 mcd i f =20ma p 2850 3600 q 3600 4500 note: measurement uncertainty of radiometric intensity: 10% bin range of dominant wavelength bin code min. max. unit condition 1 465 470 nm i f =20ma 2 470 475 note: measurement uncertainty of dominant wavelength 1.0nm bin range of forward voltage bin code min. max. unit condition 0 2.8 3.0 v i f =20ma 1 3.0 3.2 2 3.2 3.4 3 3.4 3.6 note: tolerance of forward voltage: 0.1v
datasheet lamp EALP05RDLBA0 4 copyright ? 2010, everlight americas inc. all rights reserved. relea se date : 6.jun.2012. issue no: 1 rev:1 www.everlightamericas.com 350 400 450 500 550 600 0.0 0.2 0.4 0.6 0.8 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 0 5 10 15 20 25 0 5 10 15 20 25 30 0.0 0.5 1.0 1.5 0 20 40 60 80 100 0 10 20 30 40 typical electro-optical characteristics curves relative intensity vs. wavelength (ta=25 ) directivity (ta=25 ) relative intensity (a.u.) radiation angle wavelength (nm) relative intensity (a.u.) forward current vs. forward voltage (ta=25 ) relative intensity vs. forward current (ta=25 ) forward current (ma) relative intensity(a.u.) forward voltage (v) forward current (ma) relative intensity vs. ambient temp. forward current vs. ambient temp. relative intensity(a.u.) forward current (ma) ambient temperature ta () ambient temperature ta () 25 30 35 40 45 50 55 60 65 70 0.0 0.5 1.0 1.5 2.0
datasheet lamp EALP05RDLBA0 5 copyright ? 2010, everlight americas inc. all right s reserved. release date : 6.jun.2012. issue no: 1 rev:1 www.everlightamericas.com pa ckage dimension note: B other dimensions are in millimeters, tolerance is 0 .25mm except being specified. Bprotruded resin under flange is 1.5mm max led.
datasheet lamp EALP05RDLBA0 6 copyright ? 2010, everlight americas inc. all right s reserved. release date : 6.jun.2012. issue no: 1 rev:1 www.everlightamericas.com pb el ectr ostatic electr onagnet ic magnetic or radioactive relds anti-static for 750 label moisture resistant packing materials label explanation ? cpn: customer?s product number ? p/n: product number ? qty: packing quantity ? cat: ranks of luminous intensity and forward voltag e ? hue: rank of dominant wavelength ? ref: reference ? lot no: lot number packing specification anti-electrostatic bag inner carton outside carton packing quantity 1. min 200pcs to max 500 pcs/1 bag, 5 bags/1 inner carton. 2. 10 inner cartons/1 outside carton
datasheet lamp EALP05RDLBA0 7 copyright ? 2010, everlight americas inc. all right s reserved. release date : 6.jun.2012. issue no: 1 rev:1 www.everlightamericas.com notes 1. lead forming during lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bul b. lead forming should be done before soldering. avoid stressing the led package during leads formin g. the stress to the base may damage the led?s char acteristics or it may break the leds. cut the led leadframes at room temperature. cutting the leadframes at high temperatures may cause fail ure of the leds. when mounting the leds onto a pcb, the pcb holes mu st be aligned exactly with the lead position of the led. if the leds are mounted with stress at the leads, it cause s deterioration of the epoxy resin and this will de grade the leds. 2. storage the leds should be stored at 30c or less and 70%rh or less after being shipped from everlight america s and the storage life limits are 3 months. if the leds are s tored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture a bsorbent material. please avoid rapid transitions in ambient temperatu re, especially, in high humidity environments where condensation can occur. 3. soldering careful attention should be paid during soldering. when soldering, leave more then 3mm from solder joi nt to epoxy bulb, and soldering beyond the base of the tie bar is rec ommended. recommended soldering conditions: hand soldering dip soldering temp. at tip of iron 300 max. (30w max.) preheat temp. 100 max. (60 sec max.) soldering time 3 sec max. bath temp. & time 260 max ., 5 sec max distance 3mm min.(from solder joint to epoxy bulb) distance 3mm min. (from solder joint to epoxy bulb)
datasheet lamp EALP05RDLBA0 8 copyright ? 2010, everlight americas inc. all right s reserved. release date : 6.jun.2012. issue no: 1 rev:1 www.everlightamericas.com prehead laminar wave fluxing recommended soldering profile avoiding applying any stress to the lead frame whil e the leds are at high temperature particularly whe n soldering. dip and hand soldering should not be done more than one time after soldering the leds, the epoxy bulb should be protected from mechanical shock or vibration until the leds return to room temperature. a rapid-rate process is not recommended for cooling the leds down from the peak temperature. although the recommended soldering conditions are s pecified in the above table, dip or handsoldering a t the lowest possible temperature is desirable for the leds. wave soldering parameter must be set and maintain a ccording to recommended temperature and dwell time in the solder wave. 4. cleaning when necessary, cleaning should occur only with iso propyl alcohol at room temperature for a duration o f no more than one minute. dry at room temperature before use. do not clean the leds by the ultrasonic. when it is absolutely necessary, the influence of ultrasonic cleaning on the leds depends on factors such as ultrasonic power an d the assembled condition. ultrasonic cleaning shal l be pre-qualified to ensure this will not cause damage to the led 5. heat management heat management of leds must be taken into consider ation during the design stage of led application. t he current should be de-rated appropriately by referring to th e de-rating curve found in each product specificati on. the temperature surrounding the led in the applicat ion should be controlled. please refer to the data sheet de-rating curve.
datasheet lamp EALP05RDLBA0 9 copyright ? 2010, everlight americas inc. all right s reserved. release date : 6.jun.2012. issue no: 1 rev:1 www.everlightamericas.com 6. esd (electrostatic discharge) the products are sensitive to static electricity o r surge voltage. esd can damage a die and its relia bility. when handling the products, the following measures against electrostatic discharge are strongly recommended: eliminating the charge grounded wrist strap, esd footwear, clothes, and fl oors grounded workstation equipment and tools esd table/shelf mat made of conductive materials proper grounding is required for all devices, equi pment, and machinery used in product assembly. surge protection should be considered when designin g of commercial products. if tools or equipment contain insulating materials such as glass or plastic, the following measures against electrostatic discha rge are strongly recommended: dissipating static charge with conductive materials preventing charge generation with moisture neutralizing the charge with ionizers 7. directions for use the leds should be operated with forward bias. the driving circuit must be designed so that the leds a re not subjected to forward or reverse voltage while it is off. if reverse voltage is continuously applied to the leds, it may cause migration resulting in led damage. 8. other above specification may be changed without notice. everlight americas will reserve authority on materi al change for above specification. when using this product, please observe the absolut e maximum ratings and the instructions for using ou tlined in these specification sheets. everlight americas assumes no responsibility for any damage resulting from use o f the product which does not comply with the absolute maximum ratings and the instructi ons included in these specification sheets. these specification sheets include materials protec ted under copyright of everlight americas corporati on. please don?t reproduce or cause anyone to reproduce them without everlight americas' consent.
|
